Connect. Communicate. Collaborate. Securely.

Home » Kerio User Forums » Kerio Control » KWF 5.1.10 + USB ADSL modem - KWF misunderstand local and outside connections.
  •  
Vlad135

Messages: 2
Karma: 0
Send a private message to this user
Who has met such problem?

I have Home network and connection to Internet by ADSL USB modem.
Network Profile is :
Server - WinXP Pro, one Ethernet card with local address (172.16.1.1), USB wireless access point with local address (10.10.1.1) and USB ADSL modem for an Internet. In total on Server there are 3 network interfaces - Ethernet (172.16.1.1), a wireless (10.10.1.1) and USB ADSL LAN virtual interface for the modem(169.254.20.116), and also Dial Up connection for Internet - that is the modem.
Workstations are under WinXP Hom and Pro (partly on a radio access, partly on Ethernet). KWF 5.1.10 demo I was install on the Server.
Earlier in such profile KWF did not stand (there was no radio access and used regular WinХР ICF).
I was install KWF by Wizard - option Connect over PPtP. Thus I obtained 3 local interfaces - Ethernet, wireless and USB ADSL LAN.

I wrote in file winroute.cfg in section <list name = "Interfaces"> for Dial Up and USB ADSL LAN <variable name = "Outside"> 1 </variable>, i.e. that they such as outside interfaces, and Proxy on them was not started.
I look in Admin Console section Connection Status and see, that NAT is shown like local connection, but Local Traffic is like incoming and outgoing connections, and the connection from other computer with Admin Console shows like incoming connection.
I think that is because of this virtual card USB ADSL LAN. That is necessary somewhere to change something manually in a KWF config file, but what?
  •  
Pavel Dobry (Kerio)

Messages: 5245
Karma: 251
Send a private message to this user
Vlad135 wrote on Sun, 25 April 2004 22:14

Who has met such problem?

I have Home network and connection to Internet by ADSL USB modem.
Network Profile is :
Server - WinXP Pro, one Ethernet card with local address (172.16.1.1), USB wireless access point with local address (10.10.1.1) and USB ADSL modem for an Internet. In total on Server there are 3 network interfaces - Ethernet (172.16.1.1), a wireless (10.10.1.1) and USB ADSL LAN virtual interface for the modem(169.254.20.116), and also Dial Up connection for Internet - that is the modem.
Workstations are under WinXP Hom and Pro (partly on a radio access, partly on Ethernet). KWF 5.1.10 demo I was install on the Server.
Earlier in such profile KWF did not stand (there was no radio access and used regular WinХР ICF).
I was install KWF by Wizard - option Connect over PPtP. Thus I obtained 3 local interfaces - Ethernet, wireless and USB ADSL LAN.

I wrote in file winroute.cfg in section <list name = "Interfaces"> for Dial Up and USB ADSL LAN <variable name = "Outside"> 1 </variable>, i.e. that they such as outside interfaces, and Proxy on them was not started.
I look in Admin Console section Connection Status and see, that NAT is shown like local connection, but Local Traffic is like incoming and outgoing connections, and the connection from other computer with Admin Console shows like incoming connection.
I think that is because of this virtual card USB ADSL LAN. That is necessary somewhere to change something manually in a KWF config file, but what?




Who did you tell that false information about changing configuration file?

Revert all changes that you manually made in configuration file and everything will run fine.

  •  
Vlad135

Messages: 2
Karma: 0
Send a private message to this user
Unfortunately this problem present independently from my changes in config file. I have done deep uninstall of KWF and reinstall it again by wizard option without any changes in winroute.cfg.
The problem has not vanished. Sad
Previous Topic: SIP & Voice over IP
Next Topic: www.solitaire.com
Goto Forum:
  


Disclaimer:
Kerio discussion forums are intended for open communication between forum members and may contain information and material posted by members which may be useful in learning about Kerio products. The discussion forums are not intended to provide technical support for any specific product. Any information implied or expressed in the discussion forums is that of the posting member. Kerio is in no way responsible for the information posted in the forums, or its accuracy. Kerio employees may participate in the discussions, but their postings do not represent an offical position of the company on any issues raised or discussed. Kerio reserves the right to monitor and maintain the forums to promote free and accurate exchange of information.

Current Time: Thu Nov 23 02:45:22 CET 2017

Total time taken to generate the page: 0.00374 seconds
.:: Contact :: Home ::.
Powered by: FUDforum 3.0.4.