Connect. Communicate. Collaborate. Securely.

Home » Kerio User Forums » Kerio Control » Multi ip ranges !
  •  
alaa

Messages: 25
Karma: 2
Send a private message to this user
Hello
Bellow IP are not real but i put to clear Laughing

i have Router (192.168.1.1)
Kerio server 192.168.1.5 (internet) -- this connected to router --
Laptop 192.168.1.3 -- this connected to router --
--------------------
Kerio Server 192.168.2.1 (Local) -- this connected to Kerio--
Access point 192.168.1.150 -- this connected to Kerio--

my clients connected to kerio and take DHCP 192.168.2.X
i have access point connected to kerio, any client connect to this access point and get IP 192.168.2.X which means that he get ip from Kerio server (access point DHCP disabled)
this Access point web admin login is 192.168.1.150 !! how can log into it if i use pc connected to kerio with ip 192.168.2.7

[Updated on: Thu, 06 November 2014 23:18]

  •  
Petr Dobry (Kerio)

Messages: 782
Karma: 61
Send a private message to this user
Change Access point's IP address to some from 192.168.2.x range.

[Updated on: Fri, 07 November 2014 00:31]


Petr Dobry
Product Development Manager | Kerio
  •  
alaa

Messages: 25
Karma: 2
Send a private message to this user
Petr your answer is correct 100%

i hope to get another solution to reach this access point IP web admin 192.168.1.150

lets suppose that i am away from Kerio server
but i can reach my laptop 192.168.1.3 by RDP

is it possible to reach this access point from laptop 192.168.1.3 which connected to router not kerio?

note: i always control kerio fom this laptop after adding rule in traffic rule ( Remote administration Source:Any Destination:Firewall service: Kerio Control Web Admin)

network chart
http://i57.tinypic.com/33mlp8k.jpg

[Updated on: Sat, 08 November 2014 13:26]

  •  
alaa

Messages: 25
Karma: 2
Send a private message to this user
my target is to access my access point 192.168.1.150 with current settings?
  •  
SvdH

Messages: 2
Karma: 1
Send a private message to this user
Hi,

Its not 100% clear to me if you are working with Vlan's or not?
If not and your switch supports Vlan's I would suggest to make some Vlan's.
And make rules to communicate between the different Vlan's, and put on the switch port
the 2 Vlans (eg Vlan 1 (management 192.168.1.x) Vlan 2 (DCHP 192.168.2.x)).

I am guessing that the IP address 192.168.1.150 is hard set on the AP?
Previous Topic: how to change This page has been blocked by Kerio Control! notification?
Next Topic: Kerio VPN Client 8.4.1 problem after OS X update to 10.10
Goto Forum:
  


Disclaimer:
Kerio discussion forums are intended for open communication between forum members and may contain information and material posted by members which may be useful in learning about Kerio products. The discussion forums are not intended to provide technical support for any specific product. Any information implied or expressed in the discussion forums is that of the posting member. Kerio is in no way responsible for the information posted in the forums, or its accuracy. Kerio employees may participate in the discussions, but their postings do not represent an offical position of the company on any issues raised or discussed. Kerio reserves the right to monitor and maintain the forums to promote free and accurate exchange of information.

Current Time: Sun Aug 20 03:59:46 CEST 2017

Total time taken to generate the page: 0.00454 seconds
.:: Contact :: Home ::.
Powered by: FUDforum 3.0.4.