Connect. Communicate. Collaborate. Securely.

Home » Kerio User Forums » Kerio Control » Problems with IPv6
  •  
valshare

Messages: 85
Karma: 0
Send a private message to this user
Hello,

i have problems with IPv6 setup. I have enabled IPv6 and most of the devices gets a IPv6. But if go to ipv6test.google.com, google says i have no ipv6. With Kerio Control IP Tools, i can ping a IPv6 on my local network and the autoconf temporary from my macbook

Here are my settings:

http://fs5.directupload.net/images/151213/g97hqkwe.png
http://fs5.directupload.net/images/151213/8wm7mwpm.png
http://fs5.directupload.net/images/151213/45lddao2.png
http://fs5.directupload.net/images/151213/dhzk986x.png


ifconfig from the Kerio Control:

eth7.990  Link encap:Ethernet  HWaddr 00:10:--:--:--:--  
          inet addr:10.255.250.1  Bcast:0.0.0.0  Mask:255.255.255.0
          inet6 addr: fe80::2--:f3--:fe--:af--/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:38136275 errors:0 dropped:0 overruns:0 frame:0
          TX packets:51782467 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:13630544407 (12.6 GiB)  TX bytes:64483664628 (60.0 GiB)

eth7.991  Link encap:Ethernet  HWaddr 00:10:--:--:--:--  
          inet addr:10.255.251.1  Bcast:0.0.0.0  Mask:255.255.255.0
          inet6 addr: fe80::2--:f3--:fe--:af--/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:31599440 errors:0 dropped:7 overruns:0 frame:0
          TX packets:67250883 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1898627732 (1.7 GiB)  TX bytes:99354905021 (92.5 GiB)



ifconfig from MacBookPro
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 14:10:--:--:--:-- 
	inet6 fe80::16--:9f--:fe--:b--f%en0 prefixlen 64 scopeid 0x4 
	inet 10.255.250.18 netmask 0xffffff00 broadcast 10.255.250.255
	inet6 2a--:1--:3--:fd:16--:9f--:fe--:b6-- prefixlen 64 autoconf 
	inet6 2a--:1--:3--:fd:6c--:4---:df--:16-- prefixlen 64 autoconf temporary 
	inet6 2a--:1--:3--:fc:16--:9---:fe--:b6-- prefixlen 64 deprecated autoconf 
	inet6 2a--:1--:3--:fc:3---:7---:16--:fc-- prefixlen 64 deprecated autoconf temporary 
	nd6 options=1<PERFORMNUD>
	media: autoselect
	status: active

[Updated on: Sun, 13 December 2015 13:42]

  •  
valshare

Messages: 85
Karma: 0
Send a private message to this user
no one from kerio?
  •  
Petr Dobry (Kerio)

Messages: 782
Karma: 61
Send a private message to this user
That sounds like IPv6 does not work on your WAN connection.
Check IPv6 routing table and verify you can ping ipv6test.google.com from the firewall itself.

Petr Dobry
Product Development Manager | Kerio
  •  
Petr Dobry (Kerio)

Messages: 782
Karma: 61
Send a private message to this user
And as for that red rectangle - you don't need to have public IPv6 addresse there. Computers in LAN use interface's link-local address as default GW. That's normal.

Petr Dobry
Product Development Manager | Kerio
  •  
Petr Dobry (Kerio)

Messages: 782
Karma: 61
Send a private message to this user
And also check your traffic rules if they are not limited to IPv4 only.

Petr Dobry
Product Development Manager | Kerio
  •  
valshare

Messages: 85
Karma: 0
Send a private message to this user
Hello Petr Dobry,

thanks for your feedback. In my roules there are all IP versions allowed.

From Kerio Firewall i can ping 2001:4860:4860::8888 but not iv6test.google.com. Looks the ipv6 can not found for this host. Resolving ipv6test.google.com over ipv4 works.

Previous Topic: Disable authentication
Next Topic: in kerio connect how i can deny internet access
Goto Forum:
  


Disclaimer:
Kerio discussion forums are intended for open communication between forum members and may contain information and material posted by members which may be useful in learning about Kerio products. The discussion forums are not intended to provide technical support for any specific product. Any information implied or expressed in the discussion forums is that of the posting member. Kerio is in no way responsible for the information posted in the forums, or its accuracy. Kerio employees may participate in the discussions, but their postings do not represent an offical position of the company on any issues raised or discussed. Kerio reserves the right to monitor and maintain the forums to promote free and accurate exchange of information.

Current Time: Tue Oct 17 15:06:20 CEST 2017

Total time taken to generate the page: 0.00443 seconds
.:: Contact :: Home ::.
Powered by: FUDforum 3.0.4.